安裝卷簾門時需要注意的事項

　　Precautions for installing rolling shutter doors

　　卷簾門作為重要的消防設施，常用于車庫、車間和大型場所，正確安裝是使用的前提。那么我們在安裝卷簾門的時候應該知道什么呢？接下來，讓我們來看看安裝卷簾門的注意事項。

　　As an important fire-fighting facility, rolling shutter doors are commonly used in garages, workshops, and large places, and correct installation is a prerequisite for their use. So what should we know when installing rolling shutter doors? Next, let's take a look at the precautions for installing rolling shutter doors.

　　1.安裝卷軸。

　　1. Install the scroll.

　　根據詳圖中卷軸的設計高度，確定活動支撐板在立柱或墻壁上的位置，松開膨脹螺栓的十字準線。

　　According to the design height of the scroll in the detailed drawing, determine the position of the movable support plate on the column or wall, and loosen the crosshair of the expansion bolt.

　　沖孔：用沖擊鉆沖膨脹孔要求鉆頭垂直于氣缸表面。如果個別螺孔碰到鋼筋，不能鉆孔可以適當移動，但不會影響牢固性和外觀。

　　Punching: Use an impact drill to punch the expansion hole, requiring the drill bit to be perpendicular to the surface of the cylinder. If individual screw holes touch the steel bars and cannot be drilled, they can be moved appropriately, but it will not affect the firmness and appearance.

　　2.安裝防火卷簾軸。

　　2. Install the fireproof rolling shutter shaft.

　　卷盤安裝前，先將掛板按一定方向擺好，安裝在卷盤上，然后在掛板上安裝4-6塊窗簾板，卷緊并用鐵絲固定在卷盤上。

　　Before installing the reel, first arrange the hanging board in a certain direction and install it on the reel. Then install 4-6 curtain panels on the hanging board, roll them tightly and fix them on the reel with wire.

　　提起卷軸。安裝時，先將套筒軸承和座的光軸插入卷軸的端孔，對準后擰緊軸承固定螺栓。

　　Lift up the scroll. When installing, first insert the optical axis of the sleeve bearing and seat into the end hole of the spool, align it, and then tighten the bearing fixing bolts.

　　卷好之后，你可以左右移動卷軸來調整位置。同時，用水平尺和水平管檢查卷軸的水平。調整后，光軸和卷軸完全焊接固定，光軸和軸承用螺釘固定。

　　After rolling, you can move the scroll left and right to adjust its position. At the same time, use a level ruler and a level tube to check the level of the scroll. After adjustment, the optical axis and the spool are completely welded and fixed, and the optical axis and bearings are fixed with screws.

　　吊裝卷盤時，特別注意不要損壞卷在軸上的窗簾板，用鋼絲繩用木板綁牢。

　　When hoisting the reel, special attention should be paid not to damage the curtain board rolled on the shaft. Use steel wire rope and wooden board to tie it firmly.

　　3.安裝導軌

　　3. Install the guide rail

　　確定卷簾門兩側導軌的安裝位置，用錘線釋放導軌基準線，釋放導軌連接器固定螺栓的十字準線，安裝其余連接器。連接器與導軌之間的連接采用點焊，每個連接器與導軌之間的點焊點不小于5點，點焊寬度不小于5 mm，焊縫不應磨損。使用不銹鋼導軌時，焊條采用不銹鋼焊條。

　　Determine the installation position of the guide rails on both sides of the rolling shutter door, release the guide rail reference line with a hammer line, release the crosshair of the fixing bolt of the guide rail connector, and install the remaining connectors. The connection between the connector and the guide rail is made by spot welding, with no less than 5 spot welding points between each connector and the guide rail, and a spot welding width of no less than 5mm. The weld seam should not be worn. When using stainless steel guide rails, stainless steel welding rods are used.

　　4.安裝直支撐板。

　　4. Install the straight support plate.

　　安裝主動支撐板，預先連接好驅動支架，焊接在支撐板上，用螺母、彈簧圈、平墊圈擰緊穿過支撐扳手孔的膨脹螺栓，使支撐板垂直于卷筒。支撐板用整個門的重量固定。有些支撐板雖然用膨脹螺栓固定，但不夠穩定。為了保證卷簾門的穩定性，應增加支撐或加強筋。磚墻上支撐板的現場固定、焊接和固定應使用相對的螺栓。

　　Install the active support plate, pre connect the drive bracket, weld it onto the support plate, and tighten the expansion bolt through the support wrench hole with nuts, spring coils, and flat washers to make the support plate perpendicular to the drum. The support plate is fixed with the weight of the entire door. Some support plates, although fixed with expansion bolts, are not stable enough. To ensure the stability of the rolling shutter door, support or reinforcement bars should be added. The on-site fixation, welding, and fixing of support plates on brick walls should use corresponding bolts.

　　5.安裝窗簾板

　　5. Install curtain panels

　　先松開卷簾上的幾塊簾板，用水平管和直尺檢查卷簾的粗糙度不超過孔高的1/300。如果傾斜度超出公差范圍，找出原因并進行調整。

　　First, loosen the several curtain panels on the roller blind and use a level tube and ruler to check that the roughness of the roller blind does not exceed 1/300 of the hole height. If the inclination exceeds the tolerance range, identify the cause and make adjustments.

　　利用卷軸的旋轉，放上簾板，安裝簾板的底梁。安裝卷簾門簾板時要注意頭部。另外，如果其余的簾板提前放在一起，要特別注意運動，打捆時簾板不要變形。

　　Using the rotation of the scroll, place the curtain board and install the bottom beam of the curtain board. Pay attention to the head when installing the rolling shutter door curtain panel. In addition, if the remaining curtains are placed together in advance, special attention should be paid to movement and the curtains should not deform when bundling.

　　檢查導軌上弧彎是否合適，然后放下卷簾，四處走走，看看是否有堵塞。

　　Check if the curvature on the guide rail is appropriate, then lower the roller blind and walk around to see if there is any blockage.

　　在安裝托輪架的設計中，當需要安裝托輪時，要確定門兩側墻柱上支架的位置，方法與卷軸相同。安裝支撐輪之前，先安裝支架。每個支撐輪的中間高度和水平度應統一后固定。

　　In the design of installing the idler frame, when it is necessary to install the idler, the first step is to determine the position of the brackets on the wall columns on both sides of the door, using the same method as the scroll. Before installing the support wheel, install the bracket first. The middle height and levelness of each supporting wheel should be fixed uniformly.

　　6.安裝卷簾門電機。

　　6. Install the motor for the rolling shutter door.

　　先將鏈條放在支架上的鏈輪上，固定驅動底座前先將鏈條放在小鏈輪上，然后擰緊固定螺栓，再搖動鏈條使卷軸轉動。

　　First, place the chain on the sprocket on the bracket. Before fixing the drive base, place the chain on the small sprocket, tighten the fixing bolts, and then shake the chain to rotate the reel.

　　以上內容是我們在安裝卷簾門時需要注意的一些事項。你想知道更多嗎？請關注我們的網站。希望我們的分享能給你帶來更多的幫助。

　　The above content is some things we need to pay attention to when installing rolling shutter doors. Do you want to know more? Please follow our website. I hope our sharing can bring you more help.

　　本文由  濟南卷簾門 友情奉獻.更多有關的知識請點擊  http://m.verycq.cn/   真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Rolling Shutter Doors For more related knowledge, please click http://m.verycq.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.